
Hydraulic slide beds type: AZC 8000 / AZC 9000 / AZC 10000 / AZC 11000 / AZC 12000
Standard equipment
- Installed on a vehicle having a total weight of 8,000 to 12,000 kg
- The auxiliary chassis and chassis module made of steel profiles
- The bed is made of steel profiles and steel sheet
- The bed floor is made of 4 mm thick steel sheet or 4-5 mm thick corrugated steel sheet
- The bed is lifted/lowered hydraulically, the entire bed is lowered onto the ground by sliding and tilting hydraulically, using two hydraulic tilt cylinders and one retracting/extending hydraulic cylinder
- Ramp angle: 11 – 13°
- Front safety rail next to the cabin
- All steel components of the bed may be sandblasted and double-painted in a color of customer’s choice
- The first paint layer of the upper and lower parts of the bed: 100 to 120 microns
- The second paint layer of the upper and lower parts of the bed: 100 to 120 microns
- Bed – bed floor with anti-slide coating
- Bed sides color-keyed or as per customer’s request
- Hot-galvanized auxiliary chassis and chassis module (HRN EN ISO 1461 quality standard)
- Left and right PVC wings with mounts
- PVC toolbox with mounts (800 x 500 x 500) located on the right side of the vehicle
- Side underrun protection in accordance with EC standards
- Two operating reflectors on the rail behind the cabin
- Two yellow rotating lights on the roof of the cabin
- Vehicle restraints in the front part of the bed
- Fixed rear stabilizers with 80 mm PVC wheels
- LED side end-outline lamps – 4 pcs.
- LED rear end-outline lamps – 2 pcs.
- VIME hydraulic winch – installed on the front safety panel
- Model EPH 5000 or 6000
- Pulling force: 5,000 kg or 6,000 kg
- Steel rope guide – steel rope thrust panel
- Steel rope with a diameter of 12 mm and a hitch
- Steel rope length: 25 m including the hitch
- Complete hydraulic installations and equipment
- Power chain for hydraulic tubes
- Two ramp lifting and lowering cylinders
- A ramp extending cylinder
- Winch-moving (sideways) cylinder
- 50 L gear pump
- Controlling hydraulic-pneumatic block with 4 handles / manual operation
- Located in the PVC box on the right side
- Flow rate: 50 L/min
- 40-45 L oil tank including cap and filter
- Operating and maintenance instructions
- Certified by the Vehicle Center of Croatia
Optional equipment
- Additional PVC toolbox (800 x 500 x 500) located on the left side of the vehicle
- PVC box for the fire extinguisher
- PVC water tank with mounts
- Remote radio control – 4 options (8 channels)
- Additional electro-pneumatic control valve (to roll/unroll the rope on the winch and move the winch sideways) – 2 pcs.
- Additional electro-pneumatic control valve (to roll/unroll the rope on the winch and move the winch sideways, lift and lower the bed and extend the bed) – 4 pcs.
- Rope guiding reel, installable in three positions
- LED flash signals (2 MODULES) – 12/24 V RAMP (1,200 to 1,400 mm wide / 1,400 to 1,600 mm wide)
- LED flash signals (4 MODULES) – 12/24 V RAMP
- Towing hitch without CERTIFICATION and EU plug – mounted on rear stabilizers
- Towing hitch with CERTIFICATION and EU plug
- Trailer/caravan hitch (mounted on the WINCH)
- LED operating reflector – 2 pcs., mounted on the protective element next to the cabin
- Rotating LED operating reflector – 2 pcs., mounted on the protective element next to the cabin
- LED lamp and wiring for PVC toolbox lighting
- LED lamp and wiring for PVC hydraulic divider box lighting
- Toolbox – mounted above the winch next to the cabin
- Box dimensions: 2,100 to 2,300 x 150 x 150
- Bed made of steel sheet, 3 mm thick, color-keyed and box lid made of corrugated aluminum sheet with two hinges and 2 clips for closing (a padlock may also be used to close it)
- PVC sealing rubber on the upper part of the box (the lid relies upon it).
- Power winch – pulling force depends on the load carrying capacity of the bed or is determined as per customer’s request (it may be installed on vehicles without an auxiliary drive)
- Irreversible damping valve R 1/2, one-way, to lower the bed
- Irreversible damping valve R 1/2, one-way, to move the winch sideways – 2 pcs.
Mandatory equipment to be delivered on the vehicle
- Auxiliary drives to install a hydraulic pump
- Pre-installation for bodybuilders – wiring
- Appropriate width of exterior rearview mirrors depending on the width of the bed
Technical data
HYDRAULIC SLIDE BEDS | |||||
---|---|---|---|---|---|
Type | ACZ 8000 | ACZ 9000 | ACZ 10000 | ACZ 11000 | ACZ 12000 |
Bed dimensions – length | 5,500 mm to 7,000 mm | ||||
Loading width | 5,150 mm to 6,650 mm | ||||
Bed dimensions – width | 2,300 mm to 2,450 mm / 2,500 mm | ||||
Overall load carrying capacity / kg | 8,000 | 9,000 | 10,000 | 11,000 | 12,000 |
Ramp load carrying capacity / kg | 3,000 to 3,300 | 3,500 to 3,800 | 4,100 to 4,500 | 4,800 to 5,100 | 5,300 to 5,600 |
Superstructure weight / kg | 1,500 to 2,400 | ||||
Winch | YES | YES | YES | YES | DAYES |
Rope dimensions (diameter) | fi 12 | fi 12 | fi 12 | fi 12 | fi 12 |
Pulling force | 5,000 | 5,000 | 5,000 | 6,000 | 6,000 |
Rope length | 25 | 25 | 25 | 25 | 25 |